The 8" Magic Heat Reclaimer is a smart way to save on heating bills. Install the Magic Heat Waste Heat Reclaimer in the flue (vent pipe) of any air-tight stove, furnace, or freestanding fireplace. Exhaust heat and gases travel upward through the flue, circulating around the heat-exchanger tubes.Moreover, how does a heat reclaimer work?
When you add a reclaimer to your wood stove pipe, exhaust gases heat the pipe to approximately 280 degrees Fahrenheit. When this happens the thermometer inside the reclaimer turns on. The electric-powered fan forces cold air to circulate around internal tubes heated by hot flue gases.
Additionally, what is magic heat? Magic Heat is the only UL listed heat reclaimer on the market. Magic Heat is designed for heating appliances with inside flue temperatures exceeding 350 degrees and surface temperatures of the single wall pipe below the Magic Heat exceeding 280 degrees.
Also question is, how do you install a heat reclaimer?
Install Additional Parts Install 3 sheet metal screws below the heat reclaimer to any of the elbow joints to secure them into place. The hand damper is installed below the heat reclaimer near the entrance of the stove. The pipe inside of the heat reclaimer can be the same size or bigger than the flue.
How does a wood burning stove heat water?
As you can see, our setup employs a coil of copper tubing — located inside a wood burning stove's stovepipe — to heat the water that's held in our storage tank. Hot smoke rising through the stovepipe warms the water in the copper coil, which causes it to rise (and thereby draw more cold water into the coil).
How does a magic heat work?
The pre-set thermostat automatically turns the blower fan on and off when the proper temperature is reached, forcing the warmed air through the tubes and into the room while the waste gases continue up the chimney. Magic Heat is a single piece unit that quickly installs in-line with new or existing stovepipe.How hot does a stove pipe get?
I usually get the pipe to 500 - 550 upon initial start up and close down the air to run the stove top temperature around 450. I would like to run the stove top temp to 600 as Jotul says the best range is 400-600. **All temp readings are the surface temperatures.How much heat is lost up a chimney?
What's more, between 80 and 90 percent of the heat produced by wood burned in an open fireplace is lost up the chimney. This means that for every $100 you spend on firewood, you get only $10 to $20 worth of heat. The rest goes up the chimney.How can I make my wood furnace more efficient?
How to improve your wood stove's efficiency - Get the chimney right. The chimney is a vital part of the overall wood burning stove.
- Keep the chimney clean.
- Think about positioning.
- Use dry wood.
- Use the 'top down' lighting method.
- Wait, don't just throw on logs.
- Make sure it's cold outside, or warmer inside.
Can a log burner run central heating?
Wood burning stoves can be made a part or substitute of the existing central heating system and heat the entire home as well as domestic water.How do you hook up a wood stove to a water heater?
The tank must be located very close to the wood stove to avoid long pipe runs. The drain of the water heater must connect to the input of the hot water front or coil and be higher than it. The hot water piping coming out of the hot water front, coil or U shape heater must go into the top of the range boiler.Can wood burners heat water?
A wood boiler stove provides heating and hot water and, unlike a heat pump, requires no electricity to run. From small boiler stoves which can provide a bit of hot water, to larger stoves which can easily power your whole house there is a large range to choose from.How does a log burner with back boiler work?
A wood-fuelled (biomass) stove with a back boiler is a stove that provides heat not only into the room (like a conventional stove) but hot water to run one or more radiators as well. In some instances biomass stoves with back boilers are used to provide domestic hot water as well.Can solid fuel be linked with oil fired central heating?
Everyone loves the look of a real fire and now integrated or linked-up systems allow you to utilise a solid fuel boiler alongside other heating technologies such as gas, oil, heat pumps or solar to provide maximum flexibility. The real advantage of linking up oil or gas systems with a solid fuel one is its flexibility.Can you have a log burner with a back boiler?
Log Burners With Back Boilers. Boiler stoves are multi-fuel stoves with a back boiler to give you the option of also using your multi-fuel stove to run your hot water and central heating.How does a solid fuel heating system work?
In solid fuel heating systems the fire heats up the water in the boiler, circulates it to a hot water storage cylinder, then a pump sends it to the radiators. Coal is more expensive and has a higher output than wood, but can also vary in its ash and volatile gas content - which in turn will reduce its heat output.How does a water stove work?
Air is heated in the firebox and passed through channels in the water reservoir, which is heated and pumped underground through insulated pipes to the house. A thermostat that monitors the temperature of the water in the reservoir controls the furnace draft. 
