Use rust-resistant shingle nails or staples 1-1/4" to 1-1/2" (3.2 to 3.8 cm) long, galvanized, in aluminum or stainless steel. Use 2 nails per shingle at about 3/4" (1.9 cm) from each edge, and 1" (2.5 cm) above the butt line of the overlapping shingle.Also asked, can I use roofing nails for cedar shingles?
Materials: Only corrosion resistant nails or staples shall be used in applying Eastern White Cedar shingles, hip and ridge units and starters. Stainless steel (Type 304 or 316), aluminum, or hot-dipped zinc-coated steel nails and stainless steel staples have proven to give good service.
Furthermore, is it better to nail or staple shingles? Fasteners for asphalt shingles should be roofing nails or staples. The head of a roofing nail or the crown of a staple is what actually holds a shingle in place. If staples are properly installed, they offer nearly the same wind resistance as nails.
Similarly, it is asked, what is the minimum pitch for cedar shingles?
The minimum roof pitch for shingles and shakes is 14 degrees. At these low pitches (14-22 degrees), care must be taken and a water impermeable, vapour permeable underlay MUST be used underneath, with a ventilated space between the membrane and the shingles.
How long do cedar shingles last?
50 years
What type of nails should I use for cedar siding?
Use Hot-Dipped Galvanized, Aluminum or Stainless Steel. Hot-Dipped galvanized, aluminum and stainless steel nails are all corrosion-resistant and all can be used to nail Western Red Cedar.How much is a bundle of cedar shingles?
The average price for shake roofing is around $6.30 per square foot. A square is 100 square feet and a bundle is equal to 1/3 of a square. Therefore, the average price of a square of shake is $630, and a bundle costs around $210.What is the difference between a cedar shake and shingle?
Here's the Cedar Shake & Shingle Bureau description: “Generally, a shingle is sawn on both sides and is thinner at the butt than a shake. A shake is typically split on one or both sides. … Being sawn, shingles exhibit some cross grain due to cutting, whereas shakes, being split, follow the grain more closely.How do you nail cedar siding?
Bevel siding should be face nailed to studs with 1-1/4 inch penetration into solid wood using one nail per piece spaced at a maximum of 24 inches on center. Place nail just above the overlap. Take care not to nail through the overlap of two pieces.How do you maintain cedar shake siding?
Before applying stain or paint, secure loose shakes, replace rotten or damaged ones, and fill blemishes with putty or caulk. Experts suggest the following routine maintenance for cedar siding: Check periodically for damaged or loose boards; nail down or replace as needed. Wash once a year.How are cedar shingles made?
Wood shakes and wood shingles are manufactured from western red cedar, cypress, pine and redwood trees. Shakes are split from logs and reshaped by manufacturers for commercial use. They are thicker at the butt end than shingles; generally one or both surfaces are split to obtain a textured effect.What is Cedar Undercourse?
Home > Products > Siding & Roofing > Shingles > Cedar > Cedar Undercourse Shingles. This is a utility grade shingle to be used as the under course of double coursed sidewalls and starter shingles for walls. These Eastern Cedar shingles are 18” in length and vary in width from 2-1/2” to 4”.Can you put cedar shakes over siding?
from Cedar Shake and Shingle Bureau Exterior and Interior Wall Manual. Shakes and shingles may be used to cover existing wood beveled siding, masonry, or stucco. The shakes or shingles can be applied directly over the existing siding; however, rain screen application is necessary over brick, stucco, and foam sheathing.Do cedar shingles need to be treated?
Do SBC cedar shingles need to be treated? No, the natural preservatives of cedar protect our shingles from ravages of fungi, humidity, and insects. They are often left natural and turn silver gray with time. However, they can be treated with preservatives or stains to achieve a different visual effect.What are the grades of cedar shingles?
Eastern white cedar shingles are classified by grades A, B, C and D. Eastern white cedar “A” grades have no imperfections, were as the “B” grade has imperfections above the bottom 6” but are not on the exposed face.How thick is a cedar shingle?
3/8 inch
What is a cedar shingle roof?
What is Cedar Shake Roofing? Cedar shake roofs use wooden shingles that are made from split logs. The roofs have a distinctive look because the thickness and length of each shingle can vary. This type of roofing has been in existence in North America since the days of the colonists.Can you staple Christmas lights to shingles?
Don't Put Holes in Your Roof Fans of the movie Christmas Vacation will recall Clark Griswold putting up his lights with his trusty staple gun. Stapling to your eaves (the wood part around the perimeter of your roof) is probably okay. But avoid putting staples or nails or screws or any type of hole into your shingles.How many nails do you put in a shingle?
Generally, you should use four nails per shingle. For regular three-tab shingles, this would require 320 nails per square. For high wind areas or when shingles are being applied to a mansard, six nails per shingle are required (480 nails per square).How many layers of shingles are allowed on a roof in California?
two layers
Can shingles be stapled?
When staples are installed properly, they work fine, but they're just too easy to install wrong. To know if a roof has been installed with staples, you can sometimes see the outline of the staples pushing through the shingle above. Also notice, these staples aren't perpendicular to the shingle.What are roofing staples?
Today, staples are considered an inferior method of attaching shingles to a roof, but it's easy to understand why roofers like staples. Staple guns are smaller and better balanced. Coil nail guns are literally fed with a coil of nails, and the holder for the nails makes the gun much bulkier. 
